EDUCT-O-MATIC
Clemco’s smallest closed-circuit tool, the hand-portable Educt-OMatic goes anywhere and operates on just 90 cfm of air at 90 psi.
The operator controls blasting and recovery with a trigger handle. Pulling the trigger just slightly starts the vacuum recovery. Pulling the trigger all the way starts the suction blast system.
The compact conical hopper contains the abrasive and meters it into the blast system. Air rushing through the Educt-OMatic’s mixing chamber draws the abrasive into the airstream and propels it out the nozzle.
The blast head swivels to allow blasting at any angle and the rubber boot traps
the dust and abrasive. The vacuum captures the reusable abrasive particles and sends the dust and broken abrasive to the dust bag.
The Educt-O-Matic cleans an area about one inch wide. After blasting, the operator releases the trigger about halfway to stop blasting, but continues vacuuming for two or three seconds to recover any remaining dust and abrasive. Fully releasing the trigger stops the vacuum system.
The Educt-O-Matic is designed for use with steel and iron grit. The simple cotton bag traps dust.
Educt-O-Matic Attachments:
- Flat Lip Attachment
- Serrated Attachment
- Edge Attachment
- Angle Attachment
- Master Adaptor
Includes:
1. Blast head .........................00761
2. Standard adaptor ..............00762
3. Nozzle, 3/8”, tungsten .......00754
4. Nozzle, 3/8”, steel .............00763
5. Blast jet .............................00765
6. Jet gasket..........................00766
7. Thumb screw, 1/4” x 1”.....03131
8. Blast head nipple, 3/8” x 4” .......................00767
9. Swivel connector...............00768
10. O-ring, neoprene...............00769
11. Main body..........................00770
12. Abrasive hose ...................00771
13. Thumb screw, 10-24 x 1/2” .................03887
14. Ferrule...............................00774
15. Air hose assy ....................00775
16. Suction jet .........................00776
17. Baffle assembly.................00778
18. Baffle (plastic only)........See 00778
19. Screen...........................See 00778
20. Screen gasket ...............See 00778
21. Abrasive container ............00814
22. Dust bag............................00785
23. Exhaust tube w/form .........00784
24. Valve body ........................00789
25. O-ring ................................00786
26. Valve bushing....................00792
27. Valve bushing gasket........00793
28. O-ring ................................00794
29. Washer..............................00795
30. Retaining ring....................00796
31. Spring................................00797
32. Valve stem ........................00798
33. Washer..............................00799
34. Washer, brass...................00800
35. Hex nut, 10-32 ..................03885
36. Washer, brass...................00802
37. Spring................................00803
38. Washer..............................00804
39. Eyelet, brass .....................00805
40. Washer, brass...................00806
41. Retaining ring....................00807
42. Nipple and grip assy. ........00810
43. Pipe nipple ........................00808
44. Molded handle grip ...........00812
45. Handle/yoke assy..............00811
46. Swivel nut/insert assy. ......00815
47. Container latch hook ........00782
48. Container latch..................00781
49. Master adaptor..................00757
50. Edge attachment...............00755
51. Serrated attachment..........00756
52. Angle attachment ..............00758
53. Flat lip attachment.............00759
(-) Exhaust tube gasket (not shown) .......................00846
